Adhcrete Aquaguard Grout
Adhcrete 2000 Coarse Series Grout
Adhcrete 3000 Series Epoxy Grout
Adhcrete Glittering Series Epoxy Grout
AdhCrete Adhpoxy Soft 2K Epoxy 3000-SERIES-EPOXY-GROUT-copy
ADHCRETE 2000 SUPERFINE SERIES
Package: (1 kg x 10 nos.) Cartons, (500 gm x 20 nos.) Cartons
Product Description
ADHCRETE 2000 Superfine Series grout is a fine, polymer modified, water resistant, flexible, blend of cement, graded aggregates, polymers and colour. It is designed for grouting most types of tiles including ceramics, porcelain, natural stones & glass mosaics. Incorporating ADHCRETE ADHMIX TG into the grout will increase the grout's strength, flexibility and impermeability.
Product Application
Grouting narrow joints between 1mm to 3mm,for soft bisque glazed wall tile, non-vitreous clay tile on interior and exterior floor and walls.
ADVANTAGES
- Uniform colour.
- Easy mixing & application
- Non shrinking and non cracking
- Water and whether resistance
- Hard and durable
- Economical
- Self curing when mix with ADHMIX TG
- Easy maintenance.
- Available in attractive range of colour and many more customised colour
COVERAGE
| Tile size & joint width (mm) | 2000 Superfine Series | ||
|---|---|---|---|
| 1mm | 2mm | 3mm | |
| 100 x 100 x 3 | 145 | 72 | 50 |
| 150 x 150 x 4 | 163 | 80 | 55 |
| 200 x 150 x 5 | 150 | 75 | 50 |
| 200 x 200 x 5 | 175 | 85 | 60 |
| 200 x 300 x 6 | 171 | 86 | 61 |
| 300 x 300 x 6 | 215 | 110 | 70 |
| 400 x 400 x 6 | 285 | 145 | 100 |
| 450 x 450 x 7 | 275 | 140 | 88 |
| 500 x 500 x 8 | 270 | 135 | 88 |
| 600 x 600 x 8 | 325 | 160 | 110 |
- Varies with the size and grout width, Refer AHDCrete Grout Coverage Chart or our Sales Representative.
Technical Data and Application Properties at
73° F (23° C) and 50% Relative Humidity
- Shelf Life – 1 year ( if it is stored in cool, dry place in original pack
- Mixing Ratio* – 400 ml ADHMix TG for 1 kg grout powder
- Pot Life*- Approx*1 hours
- Tensile adhesion strength(28 days)-minimum 400 PSI
- Flexural strength(28 days)- Minimum 800 PSI
- Compressive Strength(28 days)-Minimum 3000 PSI
* Specifications subject to change without prior notification and may not reflect immediately on TDS. Values shown in the table depends on laboratory condition and test procedure used .Actual field performance may vary on site condition and method of installation used. Company is not liable if failed to produce mentioned result in the site.
LIMITATIONS
- It is not recommended to use for tile with grout joint larger than 3mm
- For higher chemical resistance use ADHCrete 3000 SERIES EPOXY GROUT
- Do not clean tile joints by using acids
- Clean tile face promptly; don’t allow settling material on tile face. Seal Porous tiles before grouting.
Installation Instructions
Proper surface preparation is essential for the correct installation of any floor covering. Ensure that the adhesive has set and dried, and that tiles are firm. Before starting to grout remove spacers and other residue in grout joints and clean dust, loose material and any other contamination with wet sponge which may interface with good bond. Do not leave water standing between grout joints. Surface temperature should be maintained between 10° C to 34° C.
The standard mixing ratio is 400 ml of ADHMix TG for 1 kg of ADHCrete 2000 series superfine grout powder. Put ADHMix TG admixture in the mixing container first, and then add ADHCRET 2000 superfine series grout. Mix with hand or slow speed mixer until it’s obtaining a homogeneous lump free paste. Let the properly mixed grout paste to slake for 5 minutes and remix.
Dampen the surface with water. Using rubber float, apply the grout to a small area at a time. Completely fill the joints leaving no voids. Excess grout should be removed immediately using a rubber float held at 90° to the tiles .Float should be moved diagonally across the tiles to prevent removal of grout within the joints. Ensure that the grout completely fills the tile joints and remove the excess material.
Grout Primary Cleaning: Remove excess grout from the face of the tiles with the edge of the grout float. Hold the float at a 90° angle and pull it at a 45° angle diagonally across the joints and tile to avoid pulling out the material.
Grout Secondary Cleaning: Remove remaining grout with a damp sponge (not wet) or a damp towel. Work diagonally to the joints. Allow to dry. When the grout joints are firm polish the surface with a coarse nylon pad or coarse cloth and minimal water.
Note: Use caution when polishing soft glazed tiles or polished stone.
Download
Technical Data Sheet
Adhcrete 2000 Superfine Series
Adhcrete 2000 Coarse Series Grout
Adhcrete 3000 Series Epoxy Grout
Adhcrete Glittering Series Epoxy Grout
AdhCrete Adhpoxy Soft 2K Epoxy 3000-SERIES-EPOXY-GROUT-copy
ADHCRETE AQUAGUARD GROUT
Package: (1 kg *10 nos) Cartons 25kg bag
Color: 24 colour & many more customised colour
Product Description
It is a superior quality high polymer modified, high performance cementitious grout with hydrophobic property that allows tile joints to resist water. It is blend of Portland cement, chemical additives, graded aggregates and colour. Recommended to mix with ADHMIX TG for improved performance.
Product Application
For interior and exterior floor and walls for 1mm to 3 mm tile joint width
ADVANTAGES
- Water resistant
- Improved Stain resistant
- Smooth and one finish
- Colour-fast
- Easy maintenance
- Non shrinking and cracking
COVERAGE
| Tile size & joint width (mm) | 2000 Superfine Series | ||
|---|---|---|---|
| 1mm | 2mm | 3mm | |
| 100 x 100 x 3 | 145 | 72 | 50 |
| 150 x 150 x 4 | 163 | 80 | 55 |
| 200 x 150 x 5 | 150 | 75 | 50 |
| 200 x 200 x 5 | 175 | 85 | 60 |
| 200 x 300 x 6 | 171 | 86 | 61 |
| 300 x 300 x 6 | 215 | 110 | 70 |
| 400 x 400 x 6 | 285 | 145 | 100 |
| 450 x 450 x 7 | 275 | 140 | 88 |
| 500 x 500 x 8 | 270 | 135 | 88 |
| 600 x 600 x 8 | 325 | 160 | 110 |
- Coverage shown in the chart only for reference actual may vary depending on site condition
Technical Data and Application Properties at
73° F (23° C) and 50% Relative Humidity
- SHELF LIFE: 1 Year (If It Is Stored In Cool, Dry Place In Original Pack)
- MIXING RATIO : 400 Ml ADHMix TG For 1 Kg Grout Powder
- POT LIFE: Approximately 1 Hour
- TENSILE ADHESION STRENGTH (28 DAYS) : Minimum 400 PSI
- FLEXURAL STRENGTH (28 DAYS) : Minimum 800 PSI
*Specifications are subject to change without prior notification and may not reflect immediately on TDS. Values shown in the table depends on laboratory condition and test procedure used. Actual field performance may vary on site condition and method of installation. Company is not liable if the product fails to produce the declared result at the site
LIMITATIONS
- It is not recommended to use for tile with grout joint larger than 3mm
- For higher chemical resistance use ADHCrete 3000 SERIES EPOXY GROUT
- Do not clean tile joints by using acids
- Clean tile face promptly; don’t allow settling material on tile face. Seal Porous tiles before grouting.
Installation Instructions
Proper surface preparation is essential for the correct installation of any floor covering. Ensure that the adhesive has set and dried, and that tiles are firm. Before starting to grout remove spacers and other residue in grout joints and clean dust, loose material and any other contamination with wet sponge which may interface with good bond. Do not leave water standing between grout joints. Surface temperature should be maintained between 10° C to 34° C.
The standard mixing ratio is 400 ml of ADHMix TG for 1 kg of ADHCrete 2000 series superfine grout powder. Put ADHMix TG admixture in the mixing container first, and then add ADHCRET 2000 superfine series grout. Mix with hand or slow speed mixer until it’s obtaining a homogeneous lump free paste. Let the properly mixed grout paste to slake for 5 minutes and remix.
Dampen the surface with water. Using rubber float, apply the grout to a small area at a time. Completely fill the joints leaving no voids. Excess grout should be removed immediately using a rubber float held at 90° to the tiles. Float should be moved diagonally across the tiles to prevent removal of grout within the joints. Ensure that the grout completely fills the tile joints and remove the excess material.
Grout Primary Cleaning: Remove excess grout from the face of the tiles with the edge of the grout float. Hold the float at a 90° angle and pull it at a 45°angle diagonally across the joints and tile to avoid pulling out the material.
Grout Secondary Cleaning: Remove remaining grout with a damp sponge (not wet) or a damp towel. Work diagonally to the joints. Allow to dry. When the grout joints are firm polish the surface with a coarse nylon pad or coarse cloth and minimal water.
Note: Use caution when polishing soft glazed tiles or polished stone.
Adhcrete 2000 Superfine Series
Adhcrete Aquaguard Grout
Adhcrete 3000 Series Epoxy Grout
Adhcrete Glittering Series Epoxy Grout
AdhCrete Adhpoxy Soft 2K Epoxy 3000-SERIES-EPOXY-GROUT-copy
ADHCRETE 2000 COARSE SERIES GROUT
FLOOR & WALL THIN-SET ADHESIVE
Package: (1 kg x 10 nos.) Cartons 20 kg Bag
Product Description
ADHCRETE 2000 coarse series grout is a, polymer modified, water resistant, flexible, blend of cement, graded aggregates, polymers and colour, it is designed for grouting a tile joint 3mm-15mm, recommended ceramic quarry, terracotta, and stone tile. Incorporating ADHCRETE ADHMIX TG into the grout will increase the grout's strength, flexibility and impermeability
Product Application
Grouting joints between 3mm to 15mm, for external application, wide joints, quarry tile treated terracotta tile & slate, and ensure tiles that are not scratched easily.
ADVANTAGES
- Uniform colour
- Easy mixing & application
- Non shrinking and non cracking
- Water and whether resistance
- Hard and durable
- Economical
- Self curing when mix with ADHMix TG
- Easy maintenance.
- Available in attractive range of colour and many more customised colour
COVERAGE
| Tile size & joint width (mm) | 2000 Coarse Series | ||||
|---|---|---|---|---|---|
| 4mm | 6mm | 8mm | 10mm | 12mm | |
| 100 x 100 x 3 | 35 | 23 | 17 | 14 | 12 |
| 150 x 150 x 4 | 38 | 25 | 19 | 15 | 13 |
| 200 x 150 x 5 | 35 | 22 | 17 | 14 | 12 |
| 200 x 200 x 5 | 32 | 20 | 16 | 13 | 11 |
| 200 x 300 x 6 | 40 | 25 | 20 | 16 | 13 |
| 300 x 300 x 6 | 50 | 32 | 25 | 20 | 17 |
| 400 x 400 x 6 | 65 | 45 | 33 | 27 | 22 |
| 450 x 450 x 7 | 65 | 43 | 32 | 25 | 21 |
| 500 x 500 x 8 | 62 | 40 | 31 | 25 | 21 |
| 600 x 600 x 8 | 75 | 50 | 37 | 30 | 25 |
- *Coverage shown in the chart are only for reference. Actual may vary depending on site condition
Technical Data and Application Properties at
73° F (23° C) and 50% Relative Humidity
- Shelf Life - 1 year (if it is stored in a cool, dry place in original pack)
- Mixing Ratio - 200 ml ADHMix TG for 1 kg grout powder
- Pot Life - Approximately 2 hours
- Foot Traffic - 12 hours
- Heavy Traffic - 24 hours
- Compressive Strength(28 days)-Minimum 3000 -3500PSI
* Specifications subject to change without prior notification and may not reflect immediately on TDS. Values shown in the table depends on laboratory condition and test procedure used .Actual field performance may vary on site condition and method of installation used. Company is not liable if failed to produce mentioned result in the site.
LIMITATIONS
- It is not recommended to use for polished or glossy tile. For glossy tile use 2000 superfine series
- For higher chemical resistance use ADHCRETE 3000 SERIES EPOXY GROUT
- Do not clean tile joints by using acids
- Clean tile face promptly; don’t allow settling material on tile face. Seal Porous tiles before grouting.
Installation Instructions
Proper surface preparation is essential for the correct installation of any floor covering. Ensure that the adhesive has set and dried, and that tiles are firm. Before starting to grout remove spacers and other residue in grout joints and clean dust, loose material and any other contamination with wet sponge which may interface with good bond. Do not leave water standing between grout joints. Surface temperature should be maintained between 10° C to 34° C.
The standard mixing ratio is 200ml of ADHMix TG for 1 kg of ADHCrete 2000 coarse series grout powder. Put ADHMix TG admixture in the mixing container FIrst, and then add ADHCRETE 2000 Coarse series grout. Mix with hand or slow speed mixer until it’s obtaining a homogeneous lump free paste. Let the properly mixed grout paste to slake for 5 minutes and remix.
Dampen the surface with water. Using rubber float, apply the grout to a small area at a time. Completely FIll the joints leaving no voids. Excess grout should be removed immediately using a rubber float held at 90º to the tiles .Float should be moved diagonally across the tiles to prevent removal of grout within the joints. Ensure that the grout completely fills the tile joints and remove the excess material. Remove remaining grout with a damp sponge . Work diagonally to the joints. Allow to dry. After drying remove the remaining grout film with a damp sponge. Do not use a dry cloth for cleaning as there is risk of discolouration by rubbing dried grout into the damp joint.
Download
Technical Data Sheet
Adhcrete 2000 Superfine Series
Adhcrete Aquaguard Grout
Adhcrete 2000 Coarse Series Grout
Adhcrete Glittering Series Epoxy Grout
AdhCrete Adhpoxy Soft 2K Epoxy 3000-SERIES-EPOXY-GROUT-copy
ADHCRETE 3000 SERIES EPOXY GROUT
Package: 1 kg & 5 kg Bucket.
(1/5th unit) 1 kg
(1 full unit) 5 kg
Product Description
ADHCRETE Epoxy 3000 Series is solvent free, three component high performance,100% solid epoxies and aggregates. It contains PART A and PART B in pail and PART C in separate pouch. ADHCRETE EPOXY 3000 Series is non- sagging easy to use uniform in colour and colour fast. It is exceptionally stain resistant, impermeable, and non-flammable. ADHCRETE 3000 series epoxy grout is a very resistant to acids, alkalis and most solvent and offer maximum protection against staining and chemical attack from food, beverages, chemicals and cleaning agents. ADHCRETE 3000 Series Epoxy Grout is not affected by prolonged contact with water and has high temperature resistance.
ADHCRETE 3000 Series is supplied with mixing proportion carefully measured kit with PART A (Resin), Part B (Hardener), and Part C (Filler Powder)
APPLICATIONS
Remove all mixed epoxy grout from container and spread out on mortar board as soon as mixing is completed. Grout vertical surfaces as soon as possible after mixing. When grouting walls place epoxy on single unbounded tile or plastic sheet on floor.
Apply grout using a hard epoxy rubber float, filling all joints full and even with the surface of tile. It is important to achieve 100% fill coverage with no voids in the joints to prevent pin holes and slumping of the epoxy grout.
AREAS TO USE
- Interior & exterior applications
- Continuous immersed applications, pools, spas and steam rooms.
- Industrial, commercial, processing plants, restaurants and commercial kitchens
- Installations requiring high acid and chemical resistance
- Installations requiring clinical sanitation, hospitals laboratories and veterinary clinic
ADVANTAGES
- Uniform colour.
- Easy mixing & application
- Non shrinking and non cracking
- Water and whether resistance
- Chemical and thermal resistance
- Hard and durable
- Stain free
- Easy maintenance.
- Available in attractive range of colour and many more customised colour
LIMITATIONS
- Do not alter the mixing ratio of Part A, Part B & Part C
- Light colour may darken slightly from direct UV exposure
- Should not be used in an environment with temperature requirement 100
- All epoxies are temperature sensitive epoxies are easy to apply when temperature between 21° C to 29° C. Lower temperature will cause epoxy to become stiff and extend the initial set. Higher temperature will cause to become fluid, will accelerate the set.
- Not recommended for some manufacturing facilities where heavy solvents are used. Consult technical services on questionable installations
- Actual colour may slightly vary compare to grout shade card when colour consideration is critical, mock-up should be constructed prior to final selection and application
- When used to install tile in an area that will be continually wet (e.g. swimming pools, fountains, etc.), it is recommended that the complete installation be cured 14 days prior to full submersion with chemically treated water.
COVERAGE
| Tile size (mm) | 3000 SERIES Epoxy Grout (For 5 kg kit in sq.ft.) | ||||||
|---|---|---|---|---|---|---|---|
| 2mm | 3mm | 4mm | 6mm | 8mm | 10mm | 12mm | |
| 100 x 100 x 3 | 290 | 210 | 150 | 100 | 75 | 60 | 50 |
| 150 x 150 x 4 | 325 | 225 | 165 | 110 | 80 | 70 | 55 |
| 200 x 150 x 5 | 300 | 200 | 150 | 100 | 75 | 60 | 50 |
| 200 x 200 x 5 | 350 | 230 | 175 | 120 | 90 | 70 | 60 |
| 200 x 300 x 6 | 340 | 230 | 175 | 120 | 90 | 70 | 60 |
| 300 x 300 x 6 | 435 | 300 | 220 | 150 | 110 | 90 | 75 |
| 400 x 400 x 6 | 575 | 380 | 290 | 200 | 150 | 120 | 100 |
| 450 x 450 x 7 | 550 | 375 | 280 | 190 | 140 | 110 | 100 |
| 500 x 500 x 8 | 550 | 365 | 270 | 180 | 140 | 110 | 90 |
| 600 x 600 x 8 | 650 | 440 | 325 | 220 | 160 | 130 | 110 |
- Coverage shown in the chart only for reference actual may vary depending on site condition
Technical Data and Application Properties at
73° F (23° C) and 50% Relative Humidity
- Shelf Life is 12 months if stored between 0˚C to 43˚C in factory sealed container
- Water clean-ability > 80 min
- Initial Setting 180 min
- Service Setting < 7 days
- Compressive strength > 7500 ps
- Tensile Strength > 1500 psi
Installation Instructions
Grout joints must be clean, dry and be free from any excess adhesive or foreign material and not subjected to the temperature less than 16° C or more than 36° C. It may be necessary to take excess adhesive from the grout joints to ensuring a maximum and uniform grout joint depth is achieved. For porous or unglazed tiles, it may be necessary to dampen the joints prior to application. It is recommended that porous tiles be sealed prior to grouting to avoid staining. Tile spacers must be removed prior to grouting.
Pour entire contents of ADHCrete 3000 series epoxy Grout Part A and Part B container into a clean mixing pail. Mix with a trowel or a slow speed drill mixer until liquids are completely blended. Add ADHCRETE Part “C” Filler Powder in to a mixed liquid and mix to a uniform consistency. Mix as stiff as possible to work into the joints. Once mixed, the material must be used within the specified pot life. After this time, unused material will have stiffened and should be discarded.
Remove all mixed epoxy grout from container and spread out on mortar board as soon as mixing is completed. Grout vertical surfaces as soon as possible after mixing. When grouting walls place epoxy on single unbounded tile or plastic sheet on floor. Apply grout using a hard epoxy rubber float, filling all joints full and even with the surface of tile. It is important to achieve 100% fill coverage with no voids in the joints to prevent pin holes and slumping of the epoxy grout.
Remove excess grout by hold the float at a 90º angle and pulling the float diagonally across the grout joints using it like squeegee. Do not allow epoxy to set on face of tile.
Initial Cleaning: After 30-45 min of the application of the grout apply liberal amounts of clean water to the grouted area. Adding a few drops of dish washing liquid to the water will aid in cleanup. Using scrubbing sponge with as little pressure as possible, work in circular motion across tile to loosen epoxy film and to finish the joints smoothly. Change rinse water and sponge if build up occurs frequently to aid the clean-up. Then take a clean thick towel and drag across the tile to remove any residue.
Final Cleaning: Within 24 hours or after the grouts sets firmly do a second cleaning in similar way.
Tiles can accept light foot traffic after 24 hours and heavy traffic after 72 hours. Protect from harsh industrial cleaners for 7 days and aggressive chemical for 14 days. All grouting and cleaning should be complete within a pot life. Use only water for initial maintenance for 7 days. Avoid grouted area from dust, dirt and other contamination until it is fully cured.
Download
Technical Data Sheet
Adhcrete 2000 Superfine Series
Adhcrete Aquaguard Grout
Adhcrete 2000 Coarse Series Grout
Adhcrete 3000 Series Epoxy Grout
AdhCrete Adhpoxy Soft 2K Epoxy 3000-SERIES-EPOXY-GROUT-copy
ADHCRETE GLITTERING SERIES EPOXY GROUT
Package: 1Kg (1/5th unit) & 5Kg (1 full unit), ADHCRETE Epoxy Glittering Series is supplied with mixing proportion carefully measured kit with PART A (Resin), Part B (Hardener), and Part C (Filler Powder)
Color: Available in 40 colours and 3 Finishes - Gold, Silver and copper
Product Description
ADHCrete Epoxy Glittering series is solvent free, three component high performance,100% solid epoxies and aggregates specially designed for wall and floor to enhance aesthetics. It contains PART A and PART B in pail and PART C in separate pouch. ADHCrete Epoxy Glittering series is non-sagging easy to use uniform in colour and colour fast. It is exceptionally stain resistant, impermeable and non-flammable.
ADHCrete Epoxy Glittering Series Grout is a very resistant to acids, alkalis and most solvent and offer maximum protection against staining and chemical attack from food, beverages, chemicals and cleaning agents. ADHCrete Epoxy Glittering Series Grout is not affected by prolonged contact with water and has high temperature resistance.
APPLICATION
Remove all mixed epoxy grout from container and spread out on mortar board as soon as mixing is completed. Grout vertical surfaces as soon as possible after mixing. When grouting walls place epoxy on single unbounded tile or plastic sheet on floor.
Apply grout using a hard epoxy rubber float, filling all joints full and even with the surface of tile. It is important to achieve 100% fill coverage with no voids in the joints to prevent pin holes and slumping of the epoxy grout.
AREAS TO USE
- Interior & Exterior applications
- Hotels
- Restaurants and Commercial kitchens
- Bathrooms, Lobbies
- Swimming Pools and Showrooms
ADVANTAGES
- Good aesthetic look
- Easy mixing & application
- Non shrinking and non cracking
- Chemical and thermal resistance
- Hard and durable
- Stain free
COVERAGE
| Tile Size & Joint Width (mm) | 3000 SERIES Epoxy Grout (For 5 kg kit in sq.ft.) | ||||||
|---|---|---|---|---|---|---|---|
| 2mm | 3mm | 4mm | 6mm | 8mm | 10mm | 12mm | |
| 100 x 100 x 3 | 290 | 210 | 150 | 100 | 75 | 60 | 50 |
| 150 x 150 x 4 | 325 | 225 | 165 | 110 | 80 | 70 | 55 |
| 200 x 150 x 5 | 300 | 200 | 150 | 100 | 75 | 60 | 50 |
| 200 x 200 x 5 | 350 | 230 | 175 | 120 | 90 | 70 | 60 |
| 200 x 300 x 6 | 340 | 230 | 175 | 120 | 90 | 70 | 60 |
| 300 x 300 x 6 | 435 | 300 | 220 | 150 | 110 | 90 | 75 |
| 400 x 400 x 6 | 575 | 380 | 290 | 200 | 150 | 120 | 100 |
| 450 x 450 x 7 | 550 | 375 | 280 | 190 | 140 | 110 | 100 |
| 500 x 500 x 8 | 550 | 365 | 270 | 180 | 140 | 110 | 90 |
| 600 x 600 x 8 | 650 | 440 | 325 | 220 | 160 | 130 | 110 |
- Coverage shown in the chart only for reference actual may vary depending on site condition
LIMITATIONS
- Do not alter the mixing ratio of Part A, Part B & Part C
- Light colour may darken slightly from direct UV exposure
- Should not be used in an environment with temperature requirement 100
- All epoxies are temperature sensitive epoxies are easy to apply when temperature between 21° C to 29° C. Lower temperature will cause epoxy to become stiff and extend the initial set. Higher temperature will cause to become fluid, will accelerate the set.
- Not recommended for some manufacturing facilities where heavy solvents are used. Consult technical services on questionable installations
- Actual colour may slightly vary compare to grout shade card when colour consideration is critical, mock-up should be constructed prior to final selection and application
- When used to install tile in an area that will be continually wet (e.g. swimming pools, fountains, etc.), it is recommended that the complete installation be cured 14 days prior to full submersion with chemically treated water.
Technical Data and Application Properties at
73° F (23° C) and 50% Relative Humidity
- Shelf Life of 12 months if stored between 0ºC to 43ºC in factory sealed container
- Water clean-ability > 80 min
- Initial Setting 180 min
- Service Setting < 7 days
- Compressive strength > 7500 psi
- Tensile Strength > 1500 psi
Installation Instructions
Grout joints must be clean ,dry and be free from any excess adhesive or foreign material and not subjected to the temperature less than 16° C or more than 36° C. It may be necessary to take excess adhesive from the grout joints to ensuring a maximum and uniform grout joint depth is achieved. For porous or unglazed tiles, it may be necessary to dampen the joints prior to application. It is recommended that porous tiles be sealed prior to grouting to avoid staining. Tile spacers must be removed prior to grouting.
Pour entire contents of ADHCRETE Epoxy Glittering series Grout Part A and Part B container into a clean mixing pail. Mix with a trowel or a slow speed drill mixer until liquids are completely blended. Add ADHCRETE Part C Filler Powder in to a mixed liquid and mix to a uniform consistency. Mix as stiff as possible to work into the joints. Once mixed, the material must be used within the specified pot life. After this time, unused material will have stiffened and should be discarded.
Remove all mixed epoxy grout from container and spread out on mortar board as soon as mixing is completed. Grout vertical surfaces as soon as possible after mixing. When grouting walls place epoxy on single unbounded tile or plastic sheet on floor. Apply grout using a hard epoxy rubber float, filling all joints full and even with the surface of tile. It is important to achieve 100% fill coverage with no voids in the joints to prevent pin holes and slumping of the epoxy grout.
Remove excess grout by hold the float at a 90˚ angle and pulling the float diagonally across the grout joints using it like squeegee. Do not allow epoxy to set on face of tile.
Initial Cleaning: After 30-45 min of the application of the grout apply liberal amounts of clean water to the grouted area. Adding a few drops of dish washing liquid to the water will aid in cleanup. Using scrubbing sponge with as little pressure as possible, work in circular motion across tile to loosen epoxy film and to finish the joints smoothly. Change rinse water and sponge if build up occurs frequently to aid the clean-up. Then take a clean thick towel and drag across the tile to remove any residue.
Final Cleaning: Within 24 hours or after the grouts sets firmly do a second cleaning in similar way.
Tiles can accept light foot traffic after 24 hours and heavy traffic after 72 hours. Protect from harsh industrial cleaners for 7 days and aggressive chemical for 14 days. All grouting and cleaning should be complete within a pot life. Use only water for initial maintenance for 7 days. Protect grouted area from dust, dirt and other contamination until it is fully cured.
Adhcrete 2000 Superfine Series
Adhcrete Aquaguard Grout
Adhcrete 2000 Coarse Series Grout
Adhcrete 3000 Series Epoxy Grout
AdhCrete Glittering Series Epoxy Grout
ADHCrete ADHPOXY SOFT 2K EPOXY GROUT
Package: 1Kg, 3Kg & 5Kg Bucket
Product Description
ADHCRETE Adhpoxy high performance 100% solid two component superior quality stain free, water
resistant professional epoxy grout. Is qualified for grouting of joints on flooring & wall on glass mosaic,
ceramic tile, natural stone. Adhpoxy is thixotropic two part epoxy based formulation having excellent
resistance to wear choice special sheen effect which makes it a clearing choice of consultant fraternity.
Adhpoxy grout is not affected by prolonged contact with water and has high temperature resistant. Tile
installed with Adhpoxy can be grouted in 12 hours.
ADHCRETE Adhpoxy is supplied with mixing proportion carefully measured kit with PART-A and PART-B.
APPLICATION
Adhpoxy can be applied with a suitable serrated trowel. Open time is 1 hour. if possible it is therefore
best of apply the product immediately to a surface that will be clad within the useful the open time in
environments subjected to heavy traffic in external applications and wherever high elasticity laying
system is required.
Substrates must be compact and consistent, free from dust, oil and grease, without cracks and have
already completed the curing period of hygrometric shrinkage. Undulated areas must be corrected with
suitable smoothing and finishing products.
ADVANTAGES
Adhpoxy is a high quality product is filling liquid filler in the grout is easier than the entire distantly following equivalent product, it is suited to on residential & commercial installation.
COVERAGE
Varies with tile size and grout width. Refer ADHCrete Grout coverage Chart or our Sales Representative.
SHELF LIFE
12 month if stored between 0°c to 43°c in factory sealed container.
Installation Instructions
Surface must be structurally sound, smooth and dry. Glossy or painted surfaces must be sanded, stripped and cleaned of waxes, dust, grease, loose material and any other contamination, which may interface with good bond. Thoroughly wire brush the surface & clean the dust by air compressor or wash the surface with water. Oil & grease must be removed using de-greasing solvents. Any damaged surface must be repaired by using polymer modified repair mortar. Concrete bricks/block/wall to dry out by exposure to air for at least 28 days.
Pour entire contents of ADHCRETE Adhpoxy grout part A and part B container into a clean mixing pail. Mix with a trowel or a slow speed drill mixer. Mix as stiff as possible to work on to the joints. Once mixed the specified pot life. After this time unused materials will have stiffened and should be discarded.
- Easy and light to spread
- Use for setting all types of tile
- Ideal for swimming pools, hot tubs and other wet areas, can be submerged after only 7 days
- Very easy to clean with only water
- Use for application food processing industrial commercial, residential facilities
- laying with vertical slip on deformable substrates
| Mix ratio: | Component A:component B = 9:1 |
|---|---|
| Consistency of mix: | Thick paste |
| Density of mix (kg/m³): | 1.55kg/l |
| Pot life: | 45 minutes |
| Application temperature: | from +12°C to +30°C |
| Shear adhesion strength according to EN 12003 (N/mm²)– initial | ≥ 2 N/mm2 |
| – after water immersion | ≥ 2 N/mm2 |
| – after thermal shock | ≥ 2 N/mm2 |
| Abrasion resistance (EN 12808-2) | ≤ 250 mm3 |
| Mechanical flexural strength after 28 days in standard conditions (EN 12808-3) | ≥ 30 N/mm2 |
| Mechanical compressive strength after 28 days in standard conditions (EN 12808-3) | ≥ 45 N/mm2 |
| Shrinkage (EN 12808-4) | ≤ 1.5 mm/m |
| Water absorption after 4 hours (EN 12808-5) | ≤ 0.1 g |
Adhcrete 2000 Superfine Series
Adhcrete Aquaguard Grout
Adhcrete 2000 Coarse Series Grout
Adhcrete 3000 Series Epoxy Grout
AdhCrete Glittering Series Epoxy Grout
GROUT SHADE CARD
COLOUR SHADES -2000 Super Fine Series / 3000 Epoxy Series
41. Bright White
02. Cream White
86. Ivory
22. Beige
102. Mushroom
96. Light Grey
24. Slate Gray
109. Pink
125. Light Brown
210. Wooden Brown
112. Burgundy
401. Terracotta
108. Orange
84. Lemon Yellow
93. Light Green
94. Pista
97. Steel Grey
132. Sky Blue
134. Alpine Blue
133. Creta Blue
115. Coffee Brown
26. Metal Grey
42. Platinum
104. Jet Black
* Colour shades printed on this Shade Card may vary slightly from the actual product, due to printing variations. Colours may also differ slightly due to site conditions, mixing ratio and installation methods. Test the suitability by applying on small grouting area. We recommend to use fortify with ADHMix TG for cementitious grout to get improved mechanical property and flexibility.
For Business inquiry fill our form and Toll Free Number +91 888 443 4971