Yaderi, Kaltodu Village, Kundapur Tq. Pin - 576219

Wall Cares - Plastering, Wall Putty
ADHCrete
ADHCrete

Adhcrete Wallputty Smooth Finish

ADHCrete

Adhplast Readymade Plaster

ADHCrete

Adhcrete Wallputty

ADHCrete

ADH Paint PRIMER (Exterior)

ADHCrete

ADH Paint PRIMER

ADHCrete
ADHCrete WALLPUTTY COARSE FINISH

PACKET SIZE: 1kg, 5kg, 20 kg & 40 kg

Product Description

ADHCrete Wallputty - Coarse Finish is a high quality product made of white cement, polymer, and biocide powder. To be mixed with water at the time of application it is recommended for levelling uneven rough porous cement walls, plaster work, patching cracks and filling defective surfaces. With ease of application, it provides smooth finish for top coat application. Wall Putty is recommended for both interiors and exteriors.

APPLICATION

It is recommended for use on all type of plaster and concrete to make uneven surfaces to an even and smooth surface.

ADHCrete
ADHCrete

SURFACE PREPARATION

Surface must be clean, free from dust, grease, oil, heavy soot, chalk, mildew, etc. Chalk joints and fill holes where necessary. All old loose, flaking or peeling paint must be removed.

ADVANTAGES

  • Easy to apply
  • Anti-fungal
  • Water resistance
  • Decreases paint consumption
  • Smoothens the wall with excellent finish
  • Good compressive and tensile strength
  • Complies with national and international standards

COVERAGE

Approximately 4 to 10 sq.ft per kg for 2 coats with a maximum thickness 3 mm.

LIMITATION

  • Do not directly apply on dust, oil, grease and loosely bond particles and the like.
  • Do not apply on fungus or moss affected area.
  • Structure must be two coated cement sand smooth plaster, structurally sound and stable.

Technical Data and Application Properties at 73° F(23° C) and 50% Relative Humidity

SHELF LIFE 8 Months (If It Is Stored In Cool, Dry Place In Original Pack)
WATER DEMAND 4.5 to 6 litres for 20 kg powder Specifications subject to change without prior notification and may not reflect immediately on TDS. Values shown in the table depends on laboratory condition and test procedure used. Actual field performance may vary on site condition and method of installation used. Company is not liable if the product fails to produce the mentioned result in the site.

APPLICATION PROCEDURE

Apply one coat of the above paste onto the substrate with the trowel. The thickness allowed in one coat application is 3 mm to 5 mm. Ensure that the second coat application is be done after the first coat is totally dried. The second coat can be done with either ADHCRETE Fine Putty or ADHCRETE Coarse Putty. Always prepare a required quantity of putty paste and use it within 2.5 - 3.5 hours.

The standard mixing ratio is 4.5 to 6 Itr water for 20 kg powder. Put clean water in the mixing container first, then add ADHCRETE Wallputty. For best result, mix with mixing paddle and 1/2" heavy-duty drill. Mix with hand or slow speed mixer until its obtain a homogeneous lump free paste. Let the properly mixed putty to slake for 5 to 8 minutes. Remix again for 2 minutes and apply with the recommended putty blade.

ADHCrete
ADHCrete

Adhcrete Wallputty Coarse Finish

ADHCrete

Adhplast Readymade Plaster

ADHCrete

Adhcrete Wallputty

ADHCrete

ADH Paint PRIMER (Exterior)

ADHCrete

ADH Paint PRIMER

ADHCrete
ADHCrete WALLPUTTY SMOOTH FINISH

PACKET SIZE:1 kg, 5 kg, 20 kg, 40 kg

Product Description

ADHCrete Wallputty - Smooth Finish is a high quality product made of white cement, polymer, and biocide powder. To be mixed with water at the time of application it is recommended for levelling uneven rough porous cement walls, plaster work, patching cracks and filling defective surfaces. With ease of application, it provides smooth finish for top coat application. Wall Putty is recommended for both interiors and exteriors.

Application

It is recommended for use on all type of plaster and concrete. To make uneven surfaces to even and smooth surface. Apply two coats of paste on to the substrate with putty blade. Check first coat fully cured or not before applying second coat. Total thickness of the two coats is 1.5 mm.

Technical Data and Application Properties at 73° F (23°C) and 50% Relative Humidity

SHELF LIFE 8 months (if it is stored in a cool, dry place in original pack)
WATER DEMAND 6 to 7 litres for 20 kg powder
INITIAL SET Approximately 240 min
FINAL SET Approximately 390 Min
POT LIFE Approximately 3 To 4 Hours
TENSILE STRENGTH (28 DAYS) >1.2 Mpa
COMPRESSIVE STRENGTH (28 DAYS) >8 Mpa

Coverage

The product approximately covers an 18 sq.ft to 20 sq.ft area per 1 kg for 2 coats with maximum thickness of 1.5 mm.

Limitations

  • Do not directly apply on dust, oil, grease and loosely bond particles and the like.
  • Do not apply on fungus or moss affected area.
  • Structure must be two coated cement sand smooth plaster, structurally sound and stable

ADVANTAGES

  • Easy to apply
  • Anti-fungal
  • Water resistance
  • Decreases paint consumption
  • Smoothens the wall with excellent finish
  • Good compressive and tensile strength
  • Complies with national and international standards

Surface must be clean, free from dust, grease, oil, heavy soot, chalk, mildew, etc. Chalk joints and fill holes where necessary. All old loose, flaking or peeling paint must be removed.

The standard mixing ratio is 300 to 350 gm water for 1 kg powder. Put clean water in the mixing container first, then add ADHCRETE Wall Putty. For best results, mix with mixing paddle and 1/2" heavy —duty drill. Mix with hand or slow speed mixer until a homogeneous lump free paste is obtained. Let the properly mixed putty to slake for 5 to 8 minutes. Remix again for 2 minutes and apply with the recommended putty blade.

Apply two coat of paste on to the substrate with putty blade. Check if the first coat is fully cured or not before applying the second coat. Total thickness of the two coats is 1.5 mm.

ADHCrete
ADHCrete

Adhcrete Wallputty Coarse Finish

ADHCrete

Adhcrete Wallputty Smooth Finish

ADHCrete

Adhcrete Wallputty

ADHCrete

ADH Paint PRIMER (Exterior)

ADHCrete

ADH Paint PRIMER

ADHCrete
ADHPLAST READYMADE PLASTER

PACKET SIZE: 30 kg & 50 kg

Product Description

ADHPIast Readymade Plaster is a mix of carefully selected raw materials, Portland cement and graded fillers. Polymer modified ready to use plaster, designed to use for internal and external application. After application ideal substrate for wall putty, paint or other decorative plasters. Mix with ADHCRETE ADHMIX TBM Latex admixture for higher flexibility and better performance.

Application

Designed for interior and exterior wall plastering.

PERFORMANCE PROPERTIES

  • ADHPLAST MIXED WITH AGGREGATE AND WATER
  • POT LIFE APPROX.
  • 1 HOUR
  • TIME TO TILE ON SURFACE 14 DAYS
  • TIME TO COMPLETE CURE 28 DAYS

ADVANTAGES

  • Mixes and applies easily
  • Economical and fast
  • Self-curing saves time
  • Premixed plaster, just add water
  • Easy to use
  • Very good mechanical strength

SUITABLE SUBSTRATES

  • On concrete walls
  • Concrete walls and ceilings
  • Concrete hollow brick walls
  • Cement block walls

COVERAGE CHART

THICKNESS ADHPlast ready made Plaster ADHMix TBM WATER COVERAGE
12mm 50 kg 1 Ltr Add water depending on applicable consistancy 25±3 sqft
25mm 50 kg 1 Ltr Add water depending on applicable consistancy 14±2 sqft
35mm 50 kg 0.5 Ltr Add water depending on applicable consistancy 09±2 sqft
50mm 50 kg 0.5 Ltr Add water depending on applicable consistancy 05±2 sqft

Proper surface preparation is essential for the correct installation of any floor covering. Surface must be structurally sound, smooth, and dry. Glossy or painted surfaces must be sanded, stripped and cleaned of waxes, dust grease, loose material and any other contamination, which may interface with good bond. Surface temperature should be maintained between 10° C to 38° C for good adhesion. Concrete bricks/blocks/wall to dry out by exposure to air for at least 28 days.

Add ADHSCREED to 50% water by weight, mix and make lump free slurry. Apply slurry using brush or roller in an even thickness to the cleaned substrate. This ensures the primer is absorbed into the substrate. 25 kg bag of ADHSCREED will approximately cover 25 sq.mt

While the slurry bond coat is in a wet and tacky condition, place the plaster prepared by mixing ADHPLAST with water. Spread the plaster material on wall surface and make the surface even, taking enough care to check the required levels of walls and compact well. For hacked concrete surfaces, initially one rough plaster coat would help in building up thicknesses well.

Leave the compacted and finished plaster for a period of 14 days for air curing and install tiles using a suitable thinset adhesive.

Technical Data and Application Properties at 73°F (23°C) and 50% relative humidity

PERFORMANCE PROPERTIES

ADHPIast mixed with aggregate and water

Pot Life Approx. 1 hour
Time to Tile on surface 14 Days
Time to complete cure 28 days
ADHCrete
ADHCrete

Adhcrete Wallputty Coarse Finish

ADHCrete

Adhcrete Wallputty Smooth Finish

ADHCrete

Adhplast Readymade Plaster

ADHCrete

Adhcrete Wallputty

ADHCrete

ADH Paint PRIMER (Exterior)

ADHCrete

ADH Paint PRIMER

ADHCrete
ADHCrete ADHPRIMER

PACKET SIZE: 1 Ltr, 4 Ltr, 10 Ltr, 20 Ltr

Product Description

ADHCRETE ADHPRIMER Water Based Cement Primer is a premium quality, water based disper- sion material containing cross linking polymers and selected surface activation agents, which penetrate deep into the substrate and maximize bond strength. It is water thinnable cement primer that can be used on a wide range of substrates including cement-based plasters, gypsum-based wall boards with paper face, etc. One product for all priming applications before putty application or paint application.

Application

ADHCRETE ADHPRIMER Water Based Cement Primer can be sprayed, roller, brush or broom applied to prepared surfaces. Apply two coats for better result. Apply second coat after first coat is completely dry. Avoid puddling and allow becoming dry-to-touch (3-5 hours after application with good ventilation). For best results, and while the primer is still fresh, it should be lightly brushed to ensure a complete, uniform film has been applied. Allow the primed surface to completely dry.

ADVANTAGES

  • Easy to apply
  • Anti-fungal
  • Non-toxic
  • Quick-drying and with a smooth finish
  • Decrease paint consumption

Technical Data and Application Properties at 73° F (23° C) and 50% Relative Humidity

SHELF LIFE 12 Months (If It Is Stored In Cool, Dry Place In Original Pack)
WATER DEMAND 9 To 12 Litres For 40 Kg Powder

Specifications subject to change without prior notification and may not reflect immediately on TDS. Values shown in the table depends on laboratory condition and test procedure used. Actual field performance may vary on site condition and method of installation used. Company is not liable if the product fails to produce mentioned result in the site.

SUITABLE SUBSTRATES

  • Concrete
  • Cement Plaster
  • Cement based wall putty
  • Gypsum based wall putty
  • Acrylic Based wall putty
  • Cement Backer Boards
  • Gypsum Wall boards with paper face

COVERAGE

Approximately 70-100 sqft per kg. Will vary depending on job site conditions.

This Primer can be applied by brush. If necessary dilute with water in 1:1 ratio. Water amounts should be carefully measured to ensure proper mix ratio. Make sure the water used is of potable quality to get best results. Blend by hand or using a mixing paddle.

ADHCrete
ADHCrete

Adhcrete Wallputty Coarse Finish

ADHCrete

Adhcrete Wallputty Smooth Finish

ADHCrete

Adhplast Readymade Plaster

ADHCrete

Adhcrete Wallputty

ADHCrete

ADH Paint PRIMER (Exterior)

ADHCrete

ADH Paint PRIMER

ADHCrete
ADH Paint PRIMER (Exterior)

FINISH/SHEEN: Hi Rich Finish

USES: Exterior Primer has been manufactured for above grade masonry surfaces where a high performance primer is needed. It is efflorescent and alkali resistant and will increase and reinforce the performance of the paints. It can be used on properly prepared concrete, concrete block, brick and stucco.

PACKET SIZE: 1 Ltr, 4 Ltr, 10 Ltr and 20 Ltr

FEATURES

  • Smoothest Matt Finish
  • Burnish Resistance
  • Excellent Dirt Resistance
  • Surface Protector
  • Softness Like Real Silk
ADHCrete
ADHCrete

Adhcrete Wallputty Coarse Finish

ADHCrete

Adhcrete Wallputty Smooth Finish

ADHCrete

Adhplast Readymade Plaster

ADHCrete

Adhcrete Wallputty

ADHCrete

ADH Paint PRIMER (Exterior)

ADHCrete

ADH Paint PRIMER

ADHCrete
ADH Paint PRIMER

FINISH/SHEEN: Flat Rich Gloss Finish

USES: Interior Water Base Primer is fast drying & provides excellent hiding, holdout and spatter less application. Recommended for interior dry wall, plaster & masonry surface. It can be used for priming new or previously painted interior cementitious surfaces. It is efflorescent and alkali resistant and increases the performance of emulsion paints.

PACKET SIZE: 1 Ltr, 4 Ltr, 10 Ltr and 20 Ltr

FEATURES

  • Anti Chalking
  • Enhances Top Coat Finish
  • Excellent Adhesion
  • 2 in 1
  • Opacity And Whiteness
ADHCrete
ADHCrete

Adhcrete Wallputty Coarse Finish

ADHCrete

Adhcrete Wallputty Smooth Finish

ADHCrete

Adhplast Readymade Plaster

ADHCrete

Adhcrete Wallputty

ADHCrete

ADH Paint PRIMER (Exterior)

ADHCrete

ADH Paint PRIMER

ADHCrete
ADH Crete WALL PUTTY

FINISH/SHEEN:

ADHCrete PUTTY-LOOKS GOOD WORKS BETTER

PACKET SIZE: 40 KG

Wall Putty is used as filter or sealant on walls to cover unevenness and pinholes. It provides a smooth base for the paint and lends strength to the wall. New welcome to the new-age putty that only caters to your demand for top quantity but also offers the advantage of ADHCrete on your ADHCrete Wall Putty! ADHCrete Wall Putty is manufactured using cutting edge US technology. The special process makes sure the Putty is absolutely dry after application, which enables the wall paint to dazzle in its original, ‘Just as you selected’ shade, a blend of white cement, polymers and minerals. ADHCrete Wall Putty protects and smoothness walls, and is effective on all types of cementitious surfaces. Pure white in colour, its strong adhesive properties ensure a powerful bond between the base and the paint, making it ideal sub-surface for all interior and exterior walls.

SMART FEATURES

  • True Colour Technology
  • Truest White Putty
  • Greater Resistance to water
  • Perfect bonding with the Substract
  • Ultra Smooth Finish
  • Quick, Easy Application

For Business inquiry fill our form and Toll Free Number +91 888 443 4971