Proper surface preparation is essential for the correct installation of any floor covering. Surface must be structurally sound, smooth, and dry. Glossy or painted surfaces must be sanded, stripped and cleaned of waxes, dust grease, loose material and any other contamination, which may interface with good bond. Surface temperature should be maintained between 10° C to 38° C for good adhesion. Concrete bricks/blocks /wall to dry out by exposure to air for at least 28 days.

The standard mixing ratio is 7.5 to 8.5 ltrs of water for 30 kg. Put clean water or recommended latex admixture in the mixing container first, then add ADHCRETE AAC BLOK LAYING ADHESIVE. For best result, mix with mixing paddle and 1/2” heavy-duty drill. To mix by hand, use a margin trowel and mix vigorously. Mix with hand or slow speed mixer until its obtain a homogeneous lump free paste. Let the properly mixed adhesive to slake for 4 to 5 minutes. Remix again for 2 minutes and apply with the recommended notched trowel. Properly consistence mixed material will settle in the substrates in the form of strips (ridges) without slump when it is applied on substrates.

1)Thin bed mortar for laying blocks: Before placing mortar, ensure the block work to be dry and surfaces cleaned properly. Use properly seized notched on trowel to ensure 100% coverage under a block. Place the mixed mortar on the block work in thin layers of 2 to 3 mm (or as required by engineers at site) using trowel and place the next layer of blocks on the mortar. Keep joints between the blocks as required by the site engineers and fill the joints with the mixed mortar, using a trowel. Check the plumb of the wall while laying the blocks to keep the walls perfectly vertical to the plumb.
2) Smoothing over the block work: Before placing mixed mortar, apply a bonding layer of 1 to 2mm thick AAC Block Adhesive mortar using a trowel pressing down on the block work. Then apply AAC Block Adhesive at a thickness of 8 to 10mm and smoothen using a sponge or rubber / wooden float
3) Installation of Tiles: It can be used as thin-set adhesive to install tiles on Block /brick walls. Use proper notch trowel to installation of tiles and stone on the wall. If possible, spread in approximately one square meter at a time. Only apply as much adhesive mixture as can be covered with tiles within a open time. Check open time by touching the adhesive bed with your fingertip because open time will be vary depends on temperature and humidity.
Plastering: Plumb, square and true concrete block wall can be finished with the applications of ADHCRETE readymade plaster.

Proper surface preparation is essential for the correct installation of any floor covering. Surface must be structurally sound, smooth, and dry. Glossy or painted surfaces must be sanded, stripped and cleaned of waxes, dust grease, loose material and any other contamination, which may interface with good bond. Surface temperature should be maintained between 10° C to 38° C for good adhesion. Concrete bricks/blocks /wall to dry out by exposure to air for at least 28 days.

The standard mixing ratio is 7.5 to 8.5 ltrs of water for 30 kg. Put clean water or recommended latex admixture in the mixing container first, then add ADHCRETE AAC BLOK LAYING ADHESIVE. For best result, mix with mixing paddle and 1/2” heavy-duty drill. To mix by hand, use a margin trowel and mix vigorously. Mix with hand or slow speed mixer until its obtain a homogeneous lump free paste. Let the properly mixed adhesive to slake for 4 to 5 minutes. Remix again for 2 minutes and apply with the recommended notched trowel. Properly consistence mixed material will settle in the substrates in the form of strips (ridges) without slump when it is applied on substrates.

1)Thin bed mortar for laying blocks: Before placing mortar, ensure the block work to be dry and surfaces cleaned properly. Use properly seized notched on trowel to ensure 100% coverage under a block. Place the mixed mortar on the block work in thin layers of 2 to 3 mm (or as required by engineers at site) using trowel and place the next layer of blocks on the mortar. Keep joints between the blocks as required by the site engineers and fill the joints with the mixed mortar, using a trowel. Check the plumb of the wall while laying the blocks to keep the walls perfectly vertical to the plumb.
2) Smoothing over the block work: Before placing mixed mortar, apply a bonding layer of 1 to 2mm thick AAC Block Adhesive mortar using a trowel pressing down on the block work. Then apply AAC Block Adhesive at a thickness of 8 to 10mm and smoothen using a sponge or rubber / wooden float
3) Installation of Tiles: It can be used as thin-set adhesive to install tiles on Block /brick walls. Use proper notch trowel to installation of tiles and stone on the wall. If possible, spread in approximately one square meter at a time. Only apply as much adhesive mixture as can be covered with tiles within a open time. Check open time by touching the adhesive bed with your fingertip because open time will be vary depends on temperature and humidity.
Plastering: Plumb, square and true concrete block wall can be finished with the applications of ADHCRETE readymade plaster.